Are you planning of replacing the entire portion of sheetrock installed in your home? Wait a minute! There is no need of replacing the entire sheetrock simply due to cracks, holes and water damage. You need to simply fix the area that is found damaging. But, But, But! The repair simply depends upon the size of the damage. Make the use of a jointing compound for filling up the holes and cracks in the sheetrock. Make the use of a putty knife for covering the area of damage. And for the cracks and holes larger in size, you might need to replace the section of sheetrock or simply add patching effects to the walls.
But when it comes for the water damaging effects to the sheetrock, it might turn up into a bug problem for the home owners. As the process of repairing the water damage might be hard and even a little time consuming. But, there’s nothing to worry about because there are ways that can help you in repairing the water damaging section of sheetrock. All you’re in need of is proper tools, materials, patching compound and proper willingness to try this task on your own. Here is the list of materials and tools required for repairing holes, cracks and water damage in your sheetrock. Don’t forget to follow the steps stated for enjoying the perfect result further. A DIY project can be handled by any of the home owner and is relatively quick and easy to perform too!
Materials and tools needed for the process:
- Putty knife
- Sheetrock patch
- Paint brush
- Sand paper
- Razor knife
- Protective mask
- Working gloves
- Sheetrock mud
- Paint similar to the walls
- Safety glasses
Process of repairing holes and cracks in sheetrock:
Measuring the exact area of damage is very important because it helps in making a surety of things and materials you’ll need. Make the use of a measuring tape for measuring the dimensions of the sections damaged in the sheetrock. Well, it will also help you in determining that the area can simply be repaired or you’ll need to patch it up by using the compound. Be ready with the supplies and the tools required for the process. As most of us might not store supplies for repairing sheetrock surface, it’s advisable to make a visit to the hardware store once before you start up with the process.
Even you can purchase the supplies from any home improvement store. If you observe that the size of the hole and the cracks are larger than 2 to 3 inches in size, it’s advisable top use a gauze patch for healing or repairing the crack. This material of repair is easily available and is cheaper too to buy. You can even ask the store manager to make you understand about the process of using the patch on the damage.
With the help of a razor knife start cutting surrounding the hole in your sheetrock. It simply helps you in working in a uniform area while repairing the cracks and the holes in your sheetrock. And for the cracks and holes smaller than an inch, make the use of putty knife and also the joint compound for filling the cracks and the holes observed in your sheetrock. Spread the compound evenly to the entire area of damage. It’s advisable of using a generous amount joint compound for covering the entire damaged area in your sheetrock.
Start placing the patch on the section and cut the accurate size by using a razor knife. Make the use of drywall tape for covering each and every sides of the patch. For securing the patch completely on the sheetrock, use a generous amount of joint compound on both the sides of the tape. Cut off any extra edges that you observe on the patch. Let the joint compound dry completely do that it can confirm the patch repair. Now make the use of sandpaper for gritting up the surface and smoothening the surface completely. Sand it completely unless and until the area is smooth and sharp.
Make the use of sponge for evenly spreading the paint all over the surface of sheetrock. Don’t forget to use some amount of warm water on the sanded area. Complete the process further!
Process of repairing water damage in sheetrock:
Start the process by preparing the sheetrock mud essential and important for the water damaged section of sheetrock. By following the instructions stated on the sheetrock mud, you can easily prepare the mudding compound. But in simple words, you’ll only need some amount of water for prepare the mud. Still, it’s advisable to be sure about following each and every instruction stated on the sheetrock mud for not getting anything wrong.
But the part of foxing the water damage on the sheetrock is quite difficult. Application of the sheetrock mud should be in such a way that it happens to give a natural look. It’s advisable to wear a safety mask before you head ahead due to the harmful particles that you might inhale while fixing the damage. You might also need to sand a little bit for making the surface look perfectly smooth. Now, start applying the mud on the surface and make sure you apply it evenly to the entire damaged area. Make the use of putty knife. Take some amount of mud on the putty knife and start spreading it evenly on the surface of the sheetrock.
After the application of mud on the sheetrock is evenly applied, let is try for some hours and come back for the sanding process too! Once you observe the mud to be completely dry, start the process of sanding the patch of mud. For obtaining a perfect finished look of the surface, it’s important to sand it properly. Again it’s advisable to be protective enough for wearing the makes for preventing the harmful dust particles from the mud. Paint the patch of mud gently so that it can match up with the appearance of other sections of sheetrock.